Attachments for a Bobcat E26
A Bobcat E26 is a 5,716 lb (2.59 t) mini excavator, which puts it in the 2–4 t mini class. It takes 35 mm bucket pins on a x-change stick. 6 attachments in the Quarrymark range fit a Bobcat E26: 2 post driver hammers, 1 digging bucket, 1 ditching bucket, 1 quick coupler and 1 trenching bucket. 3 of those are a direct fit: right weight class, right pin diameter. Prices start at $1,035.20.
Bobcat E26
| Operating weight | 5,716 lb · 2.59 t |
|---|---|
| Weight class | 2–4 t · mini |
| Bucket pin diameter | 35 mm |
| Coupler / interface | X-Change |
| Machine type | Mini Excavator |
| Attachments that fit | 6 (3 direct fit) |
Operating weight is from the manufacturer’s published spec sheet. Pin diameter and coupler style are derived from that weight against our own tonnage bands. They are the right starting point for a machine in this class, not a statement about your specific unit. Verify both against your OEM spec, or send us a photo of the stick end and we will confirm it before you order.
6 attachments for a E26
We grade the fit rather than answer yes or no. Direct fit means the weight class and the mounting both check out. Fits your class means the attachment is rated for a machine of this weight and mounts pin-on. Verify first means something, usually the pin diameter, needs confirming before it ships. Telling a contractor a bucket fits when it does not is how you earn a freight claim.
Everything that fits a Bobcat E26
Post Driver Hammers for a E26
2 post driver hammers
Direct fit
BorderlineDigging Buckets for a E26
1 digging bucket
Ditching Buckets for a E26
1 ditching bucket
Quick Couplers for a E26
1 quick coupler
Buying attachments for a Bobcat E26
What size bucket fits a Bobcat E26?
Buckets from 12" up to 42" wide are rated for a Bobcat E26. The widths we stock in this class are 12", 24", 42". On a 2.59 t machine the narrow end of that range is the trenching and utility-line width, and the widest sizes are for grading and cleanup, where you are moving loose material rather than breaking ground. Go wider than the machine's rated capacity and you will feel it as lost breakout force and a tippy load at full reach, not as a fitment problem.
What pin size does a Bobcat E26 use?
A Bobcat E26 in the 2.59 t class typically runs 35 mm bucket pins on a x-change connection. That is the number to check first, because it is the one that stops a bucket going on: the weight class tells you whether the machine can lift the attachment, the pin diameter tells you whether it will physically pin up. 3 of the 6 attachments listed here are the right weight class but drilled for a different pin. They are flagged "check pin size", and a bushing kit or a quick coupler resolves them. Pin diameter is derived from the machine's operating weight against our own tonnage bands, so measure yours or send us a photo of the stick end before ordering.
Can I run a hydraulic hammer on a Bobcat E26?
Yes. 2 of our hammers are rated for a machine this size. They run 350–500 joules of impact energy, which is the range a 2.59 t carrier can actually feed. The constraint is hydraulic, not structural: the machine needs an auxiliary circuit with the flow and relief pressure the hammer is specified for, and a machine plumbed only for a thumb will not run a breaker without the second circuit. Check your auxiliary flow on the machine's spec plate, or send it to us and we will match the hammer to it.
Will a quick coupler fit a Bobcat E26?
Yes. 1 coupler in our range is rated for a machine at 2.59 t. A coupler is the single best purchase on a 2.59 t machine that changes attachments more than once a day: it turns a twenty-minute pin-and-hammer job into a thirty-second swap from the seat, and it decouples you from the 35 mm pin diameter so you can buy attachments on price and spec instead of on drilling. Free freight applies over $750.
