Attachments for a Wacker Neuson EZ50
A Wacker Neuson EZ50 is a 10,913 lb (4.95 t) mini excavator, which puts it in the 4–6 t mini class. It takes 45 mm bucket pins on a pin-on stick. 13 attachments in the Quarrymark range fit a Wacker Neuson EZ50: 5 digging buckets, 2 ditching buckets, 2 hydraulic hammers, 2 post driver hammers and 1 skeleton bucket, plus 1 trenching bucket. 4 of those are a direct fit: right weight class, right pin diameter. Prices start at $1,195.20.
Wacker Neuson EZ50
| Operating weight | 10,913 lb · 4.95 t |
|---|---|
| Weight class | 4–6 t · mini |
| Bucket pin diameter | 45 mm |
| Coupler / interface | Pin-on |
| Machine type | Mini Excavator |
| Attachments that fit | 13 (4 direct fit) |
Operating weight is from the manufacturer’s published spec sheet. Pin diameter and coupler style are derived from that weight against our own tonnage bands. They are the right starting point for a machine in this class, not a statement about your specific unit. Verify both against your OEM spec, or send us a photo of the stick end and we will confirm it before you order.
13 attachments for a EZ50
We grade the fit rather than answer yes or no. Direct fit means the weight class and the mounting both check out. Fits your class means the attachment is rated for a machine of this weight and mounts pin-on. Verify first means something, usually the pin diameter, needs confirming before it ships. Telling a contractor a bucket fits when it does not is how you earn a freight claim.
Everything that fits a Wacker Neuson EZ50
Digging Buckets for a EZ50
5 digging buckets
Direct fit
Direct fit
Direct fit
Direct fit
Check pin sizeDitching Buckets for a EZ50
2 ditching buckets
Borderline
BorderlineHydraulic Hammers for a EZ50
2 hydraulic hammers
Fits your class
Check pin sizePost Driver Hammers for a EZ50
2 post driver hammers
Fits your class
BorderlineSkeleton Buckets for a EZ50
1 skeleton bucket
Buying attachments for a Wacker Neuson EZ50
What size bucket fits a Wacker Neuson EZ50?
Buckets from 12" up to 60" wide are rated for a Wacker Neuson EZ50. The widths we stock in this class are 12", 18", 24", 30", 42", 48", 60". On a 4.95 t machine the narrow end of that range is the trenching and utility-line width, and the widest sizes are for grading and cleanup, where you are moving loose material rather than breaking ground. Go wider than the machine's rated capacity and you will feel it as lost breakout force and a tippy load at full reach, not as a fitment problem.
What pin size does a Wacker Neuson EZ50 use?
A Wacker Neuson EZ50 in the 4.95 t class typically runs 45 mm bucket pins on a pin-on connection. That is the number to check first, because it is the one that stops a bucket going on: the weight class tells you whether the machine can lift the attachment, the pin diameter tells you whether it will physically pin up. 7 of the 13 attachments listed here are the right weight class but drilled for a different pin. They are flagged "check pin size", and a bushing kit or a quick coupler resolves them. Pin diameter is derived from the machine's operating weight against our own tonnage bands, so measure yours or send us a photo of the stick end before ordering.
Can I run a hydraulic hammer on a Wacker Neuson EZ50?
Yes. 4 of our hammers are rated for a machine this size. They run 350–1,018 joules of impact energy, which is the range a 4.95 t carrier can actually feed. The constraint is hydraulic, not structural: the machine needs an auxiliary circuit with the flow and relief pressure the hammer is specified for, and a machine plumbed only for a thumb will not run a breaker without the second circuit. Check your auxiliary flow on the machine's spec plate, or send it to us and we will match the hammer to it.
Will a quick coupler fit a Wacker Neuson EZ50?
We do not currently list a coupler rated for a 4.95 t machine in this catalog. Tell us the machine's stick-end pin centres and we will source one. Call (704) 555-0140.
